The CNLe pump is developed in a service friendly design with the fewest parts possible, resulting in simplicity and minimization. The design is significant for a close coupled in-line top-pull-out pump. The compact and service friendly design limits the load capabilities but provides economical installation and reduced cost of ownership. Successfully designed for light duty pumping without compromising quality.
The DHBSe pump is characterized by a single maintenance free bearing arrangement and long spacer coupling. This provides sufficient stability for medium loads and easy access for changing spare parts without dismounting motor or piping. In general, the design reflects modularity and simplicity, as the philosophy was to develop a pump, easy to produce and simple to maintain. On top of this, parts were reduced by 30%.
This vertical in-line centrifugal pump is available in DN 40…200 – Flow from 5 to 800 m3/h and pressure up to 10 bar.
Smaller and lighter
Through general optimization we have succeeded in saving up to 15% weight on primary components. The design effort has successfully been focusing on improvement of the flow conditions inside the pump allowing increased media velocity and higher efficiency. This improvement enables downsizing and up to 40% weight reduction on the pump installation.
Reduced energy consumption
By combining IRON Pump’s considerable pump experience with the most recent in CFD analyzes, we have achieved energy savings up to 20%.
Reliability
Despite material reduction IRON Pump’s strong and well proved mechanical solutions are maintained. The two main models chosen for this program are individually featured, covering a broad variety of pump applications, on shore, for marine and for off-shore.
Ready for the future
The E-Series is in compliance with EU Directive 2009/125/EC for high efficiency end-suction pumps, thus meeting the demands for the ships of tomorrow by ensuring a lower power consumption.
|
Type: |
Centrifugal Pump |
|
Features: |
Dual bearing arrangement, Flexible coupling, Multistage |
|
Flow range: |
10 - 300 m3/h |
|
Pressure range: |
10 - 150 mLc |
|
Installation: |
Horizontal, Vertical on bulkhead |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Axial split case, Dual bearing arrangement with the impeller mounted between bearings |
|
Flow range: |
25 – 4000 m3/h |
|
Pressure range: |
10 – 150 mLc |
|
Installation: |
Horizontal, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Axial split case, Flexible coupling, Dual bearing arrangement |
|
Flow range: |
25 - 3500 m3/h |
|
Pressure range: |
10 - 100 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Self-priming, Close coupled |
|
Flow range: |
10 - 100 m3/h |
|
Pressure range: |
15 - 120 mLc |
|
Installation: |
Horizontal |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Same as CNL but with an optimated hydraulic design, reduced weight and footprint |
|
Flow range: |
10 - 800 m3/h |
|
Pressure range: |
10 - 100 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Norm pump, Back-pull-out, Dual bearing arrangement |
|
Flow range: |
10 - 1000 m3/h |
|
Pressure range: |
10 - 140 mLc |
|
Installation: |
Horizontal |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Close coupled, Top-pull-out |
|
Flow range: |
10 – 800 m3/h |
|
Pressure range: |
10 – 60 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Flexible Coupling, Dual bearing arrangement, Top-pull-out |
|
Flow range: |
10 – 1000 m3/h |
|
Pressure range: |
10 – 100 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Axial load bearing, Easy service, Spacer coupling, Top-pull-out |
|
Flow range: |
10 – 800 m3/h |
|
Pressure range: |
10 – 140 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
DHBe 400 Series |
Stainless steel |
|
Type: |
Centrifugal Pump |
|
Features: |
One stage, vertical inline, top entry |
|
Flow range: |
700 - 1200 m3/h |
|
Pressure range: |
80 - 85 mlc |
|
Installation: |
Vertical |
|
Pumped liquid: |
Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Same as DHBS but with an optimated hydraulic design, reduced weight and footprint |
|
Flow range: |
10 - 800 m3/h |
|
Pressure range: |
10 - 100 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Double volute, split casing, dual bearing |
|
Flow range: |
150-650 m3/h |
|
Pressure range: |
120-250 mLc |
|
Installation: |
Horizontal |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Axial split case, Flexible coupling, Dual bearing arrangement with the impeller mounted between bearings |
|
Flow range: |
25 – 4000 m3/h |
|
Pressure range: |
10 – 150 mLc |
|
Installation: |
Vertical, In-line |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Double volute, split casing, dual bearing |
|
Flow range: |
400-650 m3/h |
|
Pressure range: |
120-250 mLc |
|
Installation: |
Vertical |
|
Pumped liquid: |
Fresh water, Sea water |
|
Type: |
Centrifugal Pump |
|
Features: |
Double volute, split casing, dual bearing |
|
Flow range: |
150-510 m3/h |
|
Pressure range: |
120-200 mLc |
|
Installation: |
Vertical |
|
Pumped liquid: |
Fresh water, Sea water |
Regarding: Water Pumps | Ejektorer | Spare Parts | Fire Fighting Pumps
